Home > Error Code > Amana Range Error Codes

Amana Range Error Codes

Contents

Test relay contact operation 3. LS - Lid Switch Error - This error will occur if unit cannot detect the lid switch opening or closing. F1-C - Control Not Calibrated - Replace control board (clock). F7 - Shorted or Stuck Button - Check glass alignment and replace touch pad if necessary. Source

High resistance in sensor (should be about. 1100 Ω) F3 Open sensor or thermal fuse Replace sensor or thermal fuse F4 Shorted sensor Replace oven temperature sensor F6 Problem in time F3-1 - Oven Temperature Sensor/Circuit Failure - Check wire connections and oven temperature sensor. Gently pull the tab down approximately 1/4 inch or until a 'click' is heard. Check the probe for pinched wires and make sure there is no condensation or contamination on receptacle. useful source

Amana Range Parts

ERC- Welded clean relay contacts. F7 - Error Detected in Self Clean lock Circuitry - Check door latch mechanism. Amana Caloric D&M Fedders 596.####### 174.####### 960.####### 587.####### 484.####### GE Gibson Jenn Air Kelvinator 362.####### 363.####### 253.####### 629.####### 417.####### 628.####### 662.####### Litton Maycor Roper Speed Queen 747.####### 925.####### 103.####### 155.####### 647.#######

Verify CCU is working by performing diagnostic test or any cycle. Close the lid and press 'Start' to continue. Sign in to make your opinion count. Amana Furnace Error Codes Check CCU is also operational by performing a diagnostic test or any cycle.

Select the 'cancel' function and wait 60 seconds. Amana Range F1 Error Code Verify Central Control Unit (CCU) is operating properly by running a diagnostic test or any cycle. This guide is designed only as a generalized guide and is not intended to replace your owners manual, if you have problems always check the owners manual first, it may well http://www.partselect.com/JustForFun/Whirlpool-Appliance-Fault-Codes.aspx Rebuild control board if failedF1-8Shorted keyRebuild control boardF1-9Slave micro not functioningRebuild control boardF1-ACircuit board groundingRebuild control boardF1-CControl not calibratedRebuild control boardF1-ECircuit board data corruptionRebuild control boardF1-FCircuit board data corruptionRebuild control boardF1-HDoor

You will need an ohm meter to test the sensor, most oven sensors should read about 1100Ω at room temperature 60 - 80 °F (15 -27 °C), if the sensor reading Amana Air Conditioner Error Codes F3 / F4 - Open or Shorted Oven Temperature Sensor - Replace oven temperature sensor. F3 - Open Oven Temperature Sensor (RTD) - Replace oven temperature sensor (RTD). Note: Unit will attempt to unlock itself during this error six times before displaying this error code.

Amana Range F1 Error Code

Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). http://www.repairclinic.com/RepairHelp/How-To-Fix-A-Range-Stove-Oven/216-1-511278-/Amana-F3-F4-The-oven-temperature-sensor-is-either-short-circuited-or-doesn-t-have-any-continuity F1-E9 - Stack Overflow - Disconnect power for at least 30 seconds and then reconnect. Amana Range Parts Check wire harness connections between drive motor and Motor Control Unit (MCU), and between MCU and the Central Control Unit (CCU). Amana Stove Error Codes We service most of the South Central Ozarks region.

Note: If this error occurs, the door will remain locked and the drain pump will run constantly even if 'cancel' is selected. http://svbuckeye.com/error-code/amana-range-error-code.php If you get the F1 and beep, replace the ERC. That's all. They both mean the same thing, and depending on the model determines the code reference, and location of the F code. Amana Microwave Error Codes

High resistance in sensor (should be about. 1100 Ω) F3 Open sensor or thermal fuse Replace sensor or thermal fuse F4 Shorted sensor Replace sensor F6 Problem in time keeping circuit AppliancePartsPros.com is the registered trademark of AppliancePartsPros.com, Inc. Check dispenser motor for powered rotations. http://svbuckeye.com/error-code/amana-range-error-code-sab.php ERC- Welded clean relay contacts.

Add to Want to watch this again later? Amana Oven F1 Error Code To test in for faults disconnect the power to the oven then remove the sensor. Replace defective part.

Repairclinic.com Appliance Newsletters Purchase Info for Appliance Parts & Manuals » Need Parts?

Press and hold any key to clear the error code and F2 code should appear. Reset time and/or cooking operation 2. More Fun Back To Fault Codes Admiral Fault Codes Whirlpool Appliance Fault Codes Roper Fault Codes Gibson Appliance Fault Codes Hotpoint Appliance Fault Codes Kelvinator Appliance Fault Codes KitchenAid Appliance Fault Amana Oven F9 Code Lock Flashing - Latch Switch Broken - Replace latch switch.

Remember: The oven control board (clock) measures resistance of sensor circuit, not actual oven temperature. Check for stuck lock switch. Replace control. Check This Out Try unplugging unit for two minutes to see if that fixes error.

Select the 'cancel' function and wait 60 seconds. Ld - Long Drain - This error code will appear if unit takes longer than 5 minutes to pump out water to the point where the pressure switch resets. Check cooling fan in the consol and cooling fan screen F3 Open sensor, Sensor resistance exceeds 2900 Ω during Bake, Broil or Clean Check oven temperature sensor and oven temperature sensor Oven temperature sensor - What a common sensor or temp sensor looks like.

F3 The oven temperature sensor is open Check for open wire connection between EOC (Electronic Oven Control - Clock) and the oven temperature sensor. F1-8 - Shorted Key - Replace control board (clock). Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). F4 - Open Oven Temperature Sensor - Replace oven temperature sensor.

FRIGIDAIRE Range/Stove/Oven Fault Codes Version 2 Failure Code Condition Check/Repair F0 & F1 EOC (Electronic Oven Control) failure Replace F2 Oven too hot Check Bake function F3 Oven temperature sensor open F6 - Control Board Failure - Replace control board (ERC). F2 - Oven Temperature Too Hot - Replace oven temperature sensor. Working...

The oven temp has risen above 665F and the door is not locked or The temp has risen above 965F with the door locked 1. Replace failed component. Published on Jan 18, 2016I need your advice regarding Amana oven error codes.While they make great dinner ware, their appliances leave much to desire.That doesn’t help me figure out how to Replace sensor if no wiring problem.

What does an oven temp sensor look like?